I am HOPING that all it is, is the headlight switch. They were working on day and the next day, they worked for about 5 minutes then went off and haven't worked since. Anyone have any other ideas??

I put a 351w in my 63 and bought a 50$ tubular cross member and centered it up and welded it in, but I don't know about 65-66 though. Looks extremely Clean http://www.ebay.com/itm/1948-49-50-51-52-53-54-55-56-FORD-TRUCK-TUBULAR-ENGINE-CROSSMEMBER-289-302-/380661757673?pt=Vintage_Car_Truck_Parts_Acce...

Welcome from West Virginia!! King pins will normally just fold when you go around a curve.(my king pins are shot in my '63) Not so much a "thunking" noise. Check the tires for bulged or flat spots. After that I would pull a drum, make sure everything is still in there and tight.

Well between my schooling and my part-time job, I really don't have time to work on it, so I have come to the conclusion to sale it. I don't know really what to ask for it. I thinking 2500$ or so, It is subframed and tubbed (axle not narrowed) and 99.5% rust free. Has new cab mounts, floor boards, b...

Well I have found a style side bed for my 63, and have decided to lower it some. I got the old flare side bed off and working on cleaning the frame, it has already been painted just cleaning off the dirt now. http://i1118.photobucket.com/albums/k617/Enix2011/1963%20short%20bed/Zaks63nobed2.jpg http:...

I drive my truck everyday about 70 miles a day, not counting my extra running on my days off. It equals out to about 1,000 miles every 2 weeks. 13 mpg is really hurtin' right now with only having a part time job. Thank you for the information on the steering box btw, I will look into that.

Hey guys my old truck is getting the whole front end redone out of my income taxes, and I'm wondering what steering box I need to make it power steering. I am having new kingpins, tie rods, drag link, and steering box put on it. It is getting a new heart also: 302 out of a 76 Ford Granada and a C6 o...

I myself have 2 now! One to play with and one to drive everyday! Both of mine are 63's, but one is still straight axle(my DD) and the other one is sub-framed(my uni). great fun they are!!

Yea guys, It's the head gasket... but a buddy of mine and dads is taking care of it for me.. I just don't have the time to tear it down and do it.. but ill keep you all updated!

Just wondering if anyone knows when the f100 run is in Pigeon Forge TN? I would like to figure out when it is so I van plan for it. Thanks guys.

Yea I'm hoping that is all it needed.

Well guys I have 40 lbs compression in cylinder 1 and 2, and 115-125 lbs in the rest. Also did a leak down test and have 100% leakage between 1 and 2.

Just wondering if anyone knows when the f100 run is in Pigeon Forge TN? I would like to figure out when it is so I van plan for it. Thanks guys.

Yes it does still have points and the plugs were under warranty. Battery is good and it already has an alternator on it. I was afraid to drive it today. I usually drive it 70+ miles a day so I didn't know if it would make it.

So yesterday I developed a miss.. No biggy, i just changed plugs, wires, cap, and rotor.. So possibly a bad plug.. Take them out, put the old ones back in. Still has a miss, went to leave work this evening (local parts store) and my gen light comes on... Hmmmm.. Okay well my lights are still bright,...

Well the looks of my truck has changed quite a bit.. I have since had it pin-striped and put some red steelies on it!! It looks alot better now!

Me and my dad (Anthony) were there with dads (bright orange and tan) econoline and my 63 flare side (flat gray and on sunday had pin striping done). Which truck was yours?

Well my headers didn't clear so I had to take them back.. and I did find a manifold at a junk yard here close for 35$ I had to modify my exhaust pipe but it works!

Air mail? and my headers came in today... Not one of the best coatings on them, but they should work.. http://i1118.photobucket.com/albums/k617/Enix2011/DSCN9619.jpg http://i1118.photobucket.com/albums/k617/Enix2011/DSCN9618.jpg http://i1118.photobucket.com/albums/k617/Enix2011/DSCN9617.jpg http://i...

Today I ordered flowtech long tube headers before I left work.. I am hoping that they clear my clutch rod coming off the frame... we will see tomorrow.